This week on a special SiliCon edition of Maker Update a face-detecting shoulder robot friend, Victorian dress, a noisy cricket, R2 junior, wearable Gundam, walking with Wall-E, and a glove from 3D printed fabric.

This week on Maker Update, a Pi-powered portrait picture plotter, screaming plants, time for your old TV, trash kang, big bones, and a quest for animatronic perfection.

This week on Maker Update: An Arduino picture painter, tufting rugs, an RC snow speeder, DIY motion-control camera rigs, a scratch-built industrial robot arm, LED stick person costume, and an answer to the question “should I have used a 555 timer?”

This month on the Adafruit edition of Maker Update, a pocket-sized procedural MIDI sequencer, Empire State Maker Faire, a menagerie of matrices, solar powered projects, and this little cutie pie!

This week on Maker Update, servo-powered flip digits, an animated GIF photo booth, remote controlled LED eyes, a pair of ping pong launchers, soldering brass rod, interactive Totoro, and an F-clamp that can roll.

This week on Maker Update, Ghost Rider, Prop-Maker, Particle Mesh boards, Simone’s Calendar, defeating DRM, MIT’s Fiberbots, an open source cat, and a library of printable Lego bricks.

Nicole Smith (aka Penolopy Bulnick on Instructables) talks with Donald Bell about her recent projects.

This week on Maker Update, a virtual rocket controller, a light organ dress, 3D printed detergent hack, and casting with Lego bricks. This week’s Cool Tool is a 5″ Sanding Mouse.

This week on Maker Update, LEDs for your eyes, talking to your lamp, a new marble machine, the poor man’s table saw, and a giant super soaker. This week’s Cool Tool is the Kreg Rip-Cut.

This Halloween, I decided to dress up as a mad scientist. Kind of obvious, I know, but a great excuse to wire up this Adafruit Neopixel Goggle Kit I had sitting around.

To be perfectly honest, I’ve never had an easy experience with Neopixels. Somehow I always manage to burn one out, or get an unexpected glitch. My hope was that this kit would provide me with a guaranteed success, and I’m happy to say that it delivered.

The kit comes in a box with most everything you need including a Trinket micro controller (basically a tiny Arduino), a pair of plastic costume goggles, two Neopixel rings, multiple colors of wire, a surface mount JST battery connector, a small rechargeable battery pack, and USB battery charger. You will need to supply your own micro USB cable for loading code, and devise your own diffuser for the lenses (plain copy paper works fine).

You’ll also need a few tools, including a soldering iron, solder, hot glue, E6000 adhesive (optional), wire cutters/strippers, and a computer.

No printed instructions are, but the online documentation is ample and detailed, plus you’ll need to go online to download the code required for the Trinket to do its magic.

Right off the bat, the instructions have you soldering a small surface mount JST connection to the Trinket. This allows you to run the Trinket from the included battery pack, but it’s also a likely stumbling block for anyone just beginning with soldering. It’s a delicate operation.

Wiring the two Neopixel rings also presented some challenges. Despite the documentation, it was hard to get a clear idea of exactly which wires ran to which areas of the rings. After thinking it through, I came up with the right solution — but again I think this is an area where someone without experience might lose hope.

Before glueing everything in place, you’re advised to load the Arduino code to the Trinket and see if everything’s working as planned. Though the Trinket is Arduino IDE compatible (meaning it can connect to the standard Arduino software), you will need an additional download and adjustment to get things working. Again, another bump in the road for a beginner.

The Instructions also advise reinforcing some of the wiring with a few globs of E6000 adhesive. I didn’t have any, but having seen it used in so many other projects I took it as a great excuse to walk to the hardware store and buy some. Securing the rings into the goggles required hot glue, which I had plenty of.

The end result looks great and I’m happy with how these turned out. For a unique costume or cosplay showpiece, I think the $40 price of the kit is a good value. It should be noted that you can’t see through the goggles once they’re complete — they’re just meant to hang out on your head and look cool.

Cool things I learned with this kit:
-Programming a Trinket board
-Chaining together multiple NeoPixels
-Using E6000 to provide strain relief on electronic wiring
-Working with and recharging small LiPo battery packs
-Surface mount soldering (JST on Trinket)

What to watch out for:
-A little bit of tricky surface mount soldering
-Configuring Arduino software settings for use with Trinket
-Aligning Neopixel rings in goggles for symmetry
-Devising your own diffuser for the lenses (I used Frisket film)

Check Neopixel Goggle Kit price on Amazon!