Maker Project Lab
November 11, 2016 AUTHOR: Donald Bell CATEGORIES: Kits, Project Tags: , , , , , , , , , , , , , , , , , ,

Review: NeoPixel Goggle Kit

This Halloween, I decided to dress up as a mad scientist. Kind of obvious, I know, but a great excuse to wire up this Adafruit Neopixel Goggle Kit I had sitting around.

To be perfectly honest, I’ve never had an easy experience with Neopixels. Somehow I always manage to burn one out, or get an unexpected glitch. My hope was that this kit would provide me with a guaranteed success, and I’m happy to say that it delivered.

Goggle Kit Contents

The kit comes in a box with most everything you need including a Trinket micro controller (basically a tiny Arduino), a pair of plastic costume goggles, two Neopixel rings, multiple colors of wire, a surface mount JST battery connector, a small rechargeable battery pack, and USB battery charger. You will need to supply your own micro USB cable for loading code, and devise your own diffuser for the lenses (plain copy paper works fine).

Tools Needed For Goggle Kit

You’ll also need a few tools, including a soldering iron, solder, hot glue, E6000 adhesive (optional), wire cutters/strippers, and a computer.

No printed instructions are, but the online documentation is ample and detailed, plus you’ll need to go online to download the code required for the Trinket to do its magic.

Right off the bat, the instructions have you soldering a small surface mount JST connection to the Trinket. This allows you to run the Trinket from the included battery pack, but it’s also a likely stumbling block for anyone just beginning with soldering. It’s a delicate operation.

Wiring Neopixel Ring Wiring Two Neopixel Rings and trinket

Wiring the two Neopixel rings also presented some challenges. Despite the documentation, it was hard to get a clear idea of exactly which wires ran to which areas of the rings. After thinking it through, I came up with the right solution — but again I think this is an area where someone without experience might lose hope.

Before glueing everything in place, you’re advised to load the Arduino code to the Trinket and see if everything’s working as planned. Though the Trinket is Arduino IDE compatible (meaning it can connect to the standard Arduino software), you will need an additional download and adjustment to get things working. Again, another bump in the road for a beginner.

Trinket Wiring Closeup Neopixel ring Wiring Closeup

The Instructions also advise reinforcing some of the wiring with a few globs of E6000 adhesive. I didn’t have any, but having seen it used in so many other projects I took it as a great excuse to walk to the hardware store and buy some. Securing the rings into the goggles required hot glue, which I had plenty of.

The end result looks great and I’m happy with how these turned out. For a unique costume or cosplay showpiece, I think the $40 price of the kit is a good value. It should be noted that you can’t see through the goggles once they’re complete — they’re just meant to hang out on your head and look cool.

Goggle components wired without goggles Goggles without components

Cool things I learned with this kit:
-Programming a Trinket board
-Chaining together multiple NeoPixels
-Using E6000 to provide strain relief on electronic wiring
-Working with and recharging small LiPo battery packs
-Surface mount soldering (JST on Trinket)

Finished Neopixel Goggles

What to watch out for:
-A little bit of tricky surface mount soldering
-Configuring Arduino software settings for use with Trinket
-Aligning Neopixel rings in goggles for symmetry
-Devising your own diffuser for the lenses (I used Frisket film)

Check Neopixel Goggle Kit price on Amazon!

October 17, 2016 AUTHOR: Donald Bell CATEGORIES: Project Tags: , , , , , , , , , , , , ,

$5 DIY Poké Ball

My DIY Pokeball made from $5 in materials.

My son’s going as Pokémon Trainer Ash Ketchum for Halloween this year, so I was inspired to make him a Poké Ball for his costume.

I was initially inspired by this Instructable, which also uses a plastic Christmas ornament. I took it in a different direction by using the grommet and furniture glider, and using acrylic paint on the inside. You can get a pretty good feel for the project from the photos I posted on Imgur (embedded below).

Items you’ll need (Amazon links):

DIY Pokeball

October 12, 2016 AUTHOR: Donald Bell CATEGORIES: News Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

Maker Update #06: Garbage Ghosts & Key Bangers

This week’s Maker Update is dedicated to taking your Halloween up a notch, with tips on costume resources, cheap and easy (and scary) DIY ghosts, 3D printed cosplay props, and site recommendations for professional haunted house props and controllers.

Read More

Sign the Mailing List

Occasional emails, nothing spammy.
* = required field

powered by MailChimp!